2026-11-06 · Lucia Bianchi · Textile note

Fabric Quality Checklist: 5 Things I Check Before Any Tencel or Blend Goes to Production

A quality manager's 5-step fabric inspection checklist covering fiber verification, knit structure (including jacquard knit), colorfastness, and batch consistency — for Tencel lyocell sheets, Tencel turtlenecks, polyester durags, and blended knit fabrics.

Fabric Quality Checklist: 5 Things I Check Before Any Tencel or Blend Goes to Production

I review fabric specifications — Tencel lyocell sheets for bedding, knit fabrics for apparel, polyester accessories — roughly 1,100 items a year. In 2024, I rejected around 12% of first-article fabric deliveries due to spec discrepancies. Most were avoidable.

This is the checklist I run before signing off on any new specification for mass production. It works for Tencel blends, 100% lyocell, and polyester blends. The layout is the same; only the thresholds change.

1. Lock the Fiber Content and Blend Ratio Before You Compare Hand-Feel

The first move is not touching the fabric. It's reading the lab report and the label claim.

A Tencel lyocell sheet labeled "100% lyocell" looks clean on paper. But blends are common, and the blend ratio changes how the fabric drapes and wears after washing. A Tencel turtleneck with 30% cotton added behaves differently from a 100% lyocell one. That's not automatically bad — but it needs to be intentional.

Here's what I mark on the spec sheet:

  • Primary fiber percentage, with tolerance (usually ±3%)
  • Blend partner (cotton, linen, polyester) and exact ratio
  • Woven vs. knit — for the same blend

The common way this step gets skipped: a supplier changes the blend ratio during the dyeing stage and reports it — but the spec sheet in the CRM doesn't get updated. You approved one thing. Production ran another.

2. Understand the Knit Structure — and Why Jacquard Matters

If you're sourcing high quality knit fabric, the term jacquard knit fabric will come up. What is jacquard knit fabric, plainly? It's a knit where the pattern is built into the fabric through stitch variation, not printed onto the finished surface. The pattern is structural — meaning it doesn't peel or wash off.

But that structural quality comes with an inspection trade-off: jacquard knits are harder to police for consistency. The "same" pattern can shift 2–3 mm between batches in ways a plain jersey never would.

What I require on a jacquard knit spec:

  • Gauge and stitch density (needles per inch, courses per cm)
  • Pattern repeat dimensions, with tolerance — not a single number
  • Yarn lot traceability for the jacquard section

It took me about two years to take "pattern repeat, with tolerance" seriously. The assumption was that jacquard is jacquard. It's not. The repeat drifts because the yarn thickness varies by lot, and the machine tensioner isn't perfectly consistent across a long run.

3. Check Colorfastness — Not Just Color Matching

Color matching is the part everyone checks. Spectrophotometer, visual match under D65 lighting, reference swatch. That routine is necessary. But colorfastness is the issue that's quieter and shows up later.

Take a polyester durag — simple product, right? Polyester holds dye well, but dark and indigo shades with post-dye finishes can bleed if the finishing process gets rushed. I've seen customer complaints surface after the first wash, not before.

Three tests I require:

  • Wash fastness (ISO 105-C06 or equivalent) — minimum grade 4
  • Rubbing fastness, both dry and wet (ISO 105-X12)
  • Light fastness for anything used outdoors or near a window (ISO 105-B02)

The wet rubbing test is the one most people skip. It's harsher than dry rubbing, and it tells you how the dye actually bonded to the fiber — not just whether it's sitting on the surface.

One more thing: colorfastness on dark lyocell can look fine on a lab swatch and still fail after three home washes. I now require a minimum of three wash cycles in the pre-production test, not one.

4. Test Finished-Garment Behavior — Not Just the Swatch

When I started this role, the swatch was the standard. If the swatch passed, you approved. That thinking broke down for us around 2019. We received a batch of Tencel blend fabric where the lab report matched spec, the swatch looked correct, and the first production run came out wrong.

The cause was pH control in the dye bath — something not captured in the lab tests and not visible in the swatch, but obvious at batch scale. It cost us six weeks of rework and a delayed delivery.

Since then, I've added two checks that I run on finished pieces, separate from the lab tests:

  • Shrinkage testing on Tencel blends: anywhere from 4–6% on an un-pre-shrunk fabric after industrial washing, unless dimensional stability is built into the finish.
  • Pilling testing: polyester blends with a heavy brushed finish will pill after the first few washes if the fiber staple length isn't controlled.

Yes, these cost more. Roughly $400–600 per fabric spec, depending on the test menu. But I've had to rework entire production runs three times for skipping them. The math isn't close.

5. Verify Batch-to-Batch Consistency Against the Golden Sample

This is the step most people skip. The swatch is approved, and everyone assumes production will follow it. But production involves different yarn lots, different dye vessels, maybe a different operator.

What I do now is keep a "golden sample" — the exact swatch that was approved. Every production delivery, I take three random pieces from the batch and compare them against the golden sample side by side. It's low-tech. But it catches things the spec sheet doesn't.

If the batch fabric doesn't match the golden sample, it doesn't go to the line. Not negotiable, regardless of what the paperwork says.

Before You Start Running This Checklist

If you're adopting this for the first time, start with two items. Fiber verification and colorfastness catch the majority of problems. Knit structure and consistency checks are worth adding once you're at volume.

One issue I see repeatedly: a supplier's spec sheet is years old, but the fabric has quietly changed. Running a spec review every six months saves you from approving the wrong thing without knowing it.

And one thing that's genuinely changed — not the fundamentals, but the execution: five years ago, you could judge fabric quality by hand-feel. Now you can't. A polyester blend can feel like wool or like plastic depending on the finish, the blend ratio, and batch control. Hand-feel will steer you wrong. Go by the numbers first, then confirm with hand-feel. Not the other way around.

The quality managers who relied on touch alone in 2020 have mostly added testing to their process by now. The ones who didn't are still reworking second shipments.


Continue the fabric discussion

For article-specific questions, use the contact brief with the intended use, composition, weight, weave, colour and required evidence.

Open the Brief